.
Page Contents
Why did my cooler suddenly stop working?
Water cooler troubleshooting
Very often if your water cooler is not working, the problem can be traced to the power supply. So as a first step, check that it is properly plugged in at the wall and the mains power is turned on. If it is switched on but not dispensing water, the next step is to check your water supply.
How do you lubricate an evaporative cooler motor?
How do you fix a swamp cooler?
How do you troubleshoot an evaporative cooler?
Troubleshooting common Evaporative cooling issues / faults:
- Check power is ON, and the circuit breaker has not been tripped.
- Check the water supply to the unit is turned ON.
- Check time delay, usually can take up to 10 minutes to start.
- Check the pump has been selected on the wall control.
Can I put a larger motor in my swamp cooler?
Motor Pulley Selection: The motor pulley must be the same size and type recommended by cooler manufacturer. Do not use a larger pulley size.
Why does my swamp cooler pump keep burning out?
You don’t want excessive water; you just want enough water to keep the pads consistently wet,” said Garcia. Garcia said when your swamp gets overworked in this heat, a pump could burn out or a belt could get worn out and snap. Keep an eye on it in case it needs replacing.
How do you reset an evaporative cooler?
You can reset the cooler by pressing the auto button on the controller and holding it for a few seconds or by resetting the power in your home at the circuit breaker.
Is it OK to run a swamp cooler 24 7? A swamp cooler can be in operation for 24 hours of the day, but you will need to ensure it has enough water. Continuous flow coolers will automatically work and will be fine to run all day. Manual swamp coolers require you to add water to the reservoir and change the settings so it will run all day efficiently.
What is the life expectancy of a swamp cooler?
But, while swamp coolers don’t cost much to buy, they are a lot of work and money to maintain. Not only that, they are only warrantied to work for 5 years. Refrigerated air systems can last up to 20 years if properly maintained.
How long do evaporative coolers last?
But, while swamp coolers don’t cost much to buy, they are a lot of work and money to maintain. Not only that, they are only warrantied to work for 5 years. Refrigerated air systems can last up to 20 years if properly maintained.
When should you replace a swamp cooler?
When Do You Need To Replace Evaporative Cooler Pads? Generally, it is recommended to clean the pads at least once every year or twice a year (before and after use) and replace them after 2-3 years.
When should I get a new swamp cooler?
The airflow is either non-existent or not cool enough. Cool airflow is the primary purpose of a swamp cooler, so if your unit’s not delivering, you’ll want to have it inspected. If the issues run too deep and new parts can’t fix the problem, a new unit may be the solution.
Why do they put swamp coolers on the roof?
The roof is usually the best place to install a swamp cooler. By putting it on the roof, it’s a lot easier to connect it to your duct system and therefore pump cool air throughout your house.
How often should I clean my swamp cooler? For homeowners that have Mastercool swamp coolers and a water softening system on their home, you should clean the pads annually and replace them every 3-5 years.
Should I remove my swamp cooler? Swamp coolers can be removed due to issues that may arise after they have gotten old or because the homeowner wants to modernize their cooling system. After a while swamp coolers can run into problems such as corrosion and water damage, not cooling the home sufficiently, and water leaks.
Do swamp cooler motors need oil?
Note that most swamp cooler units have sealed bearings that do not require added lubrication. If you have an old unit that has a lubrication port on the top of each bearing (usually there is one bearing on each side of the fan), this is an indication that you need to lubricate the bearings.
How tight should the belt be on a swamp cooler?
How do you clean a swamp cooler pump?
Clean the water reservoir at the bottom of the cooling unit at least once a month during summer to keep deposits at bay. When cleaning, you should turn off the cooling unit, then scrub it with a stiff brush soaked in water and vinegar mixture. After scrubbing, rinse the cooling unit with fresh water.
Why does my swamp cooler make noise?
The belt on the motor of your swamp cooler can make a variety of sounds. For instance, if it’s too loose, it might start squealing. The belt might also make a thumping noise when it’s bad. The repair technician can probably diagnose problems with the belt just by listening to the noise your swamp cooler makes.
Can I run my swamp cooler without the pump on?
Yes, the fan and pump motors are separate systems. You can run one without the other with no damage to the product. That said, however, you will not receive the same degree of cooling by only running the fan. For evaporative cooling to happen, water must be running over the evaporative media.
Why is my swamp cooler making noise?
The belt on the motor of your swamp cooler can make a variety of sounds. For instance, if it’s too loose, it might start squealing. The belt might also make a thumping noise when it’s bad. The repair technician can probably diagnose problems with the belt just by listening to the noise your swamp cooler makes.
Why is my swamp cooler blowing out warm air?
Check the pads—Many times a problem with the absorbent pads causes a swamp cooler to blow warm or hot air. Over time the pads lose their absorbency and don’t hold enough water to make the evaporative process work efficiently.
How do you test a swamp cooler? Check the water level in the bottom tray. It should be about one inch below the top of the tray, and below the top of the overflow pipe. If the water level is too high or too low, adjust the float arm. Make sure your float valve is working properly.
