R60 Required Thickness of Insulation Materials
| Insulation Material | Thickness Required for R60 |
|---|---|
| Fiberglass (Loose-fill) | 16-20 inches |
| Spray foam (Closed-cell) | 6-10 inches |
| Spray foam (Open-cell) | 10-14 inches |
| Cellulose (Loose-fill) | 15-20 inches |
• Nov 20, 2021.
Page Contents
Can you put too much insulation in your attic?
It’s possible to over-insulate an attic as too much will cause moisture buildup and eventually result in mold. Eventually, adding more insulation leads to diminishing returns in trapping heat as well.
What is the R-value of 14 inches of blown insulation?
Cold Climates (R-49 to R-60):
Fiberglass (batts): 14” – 19” Cellulose (blown): 14” – 18” Rock Wool (loose): 17” – 25”
Is blown-in insulation cheaper than rolls?
Blown-in insulation is typically more expensive than rolled insulation. However, this difference isn’t by that much. Blow-in insulation can cost between $1 to $1.50 per square foot. Rolled insulation, on the other hand, can be purchased for well under $1 per square foot.
How thick should my attic insulation be?
The recommended level for most attics is to insulate to R-38 or about 10 to 14 inches, depending on insulation type.
Does blown in insulation lose R-value over time?
Over time, the aeration in cellulose insulation will decrease. This settling will cause cellulose insulation to lose up to 20 percent of its R-value.
How long does blown in insulation last?
How Long Does Blown in Attic Insulation Last? Regardless of what kind of insulation you choose, blown insulation is a permanent solution. Cellulose insulation lasts 20-30 years because it is made from recycled natural materials, whereas fiberglass materials will last much longer because it does not degrade.
What is the R-value of 12 inches of blown insulation?
Blown fiberglass installed in the attic has an R-value of 2.2 per inch, so 12 inches of it would give you an R-value of 26.4 in your attic installation project.
Is R-38 insulation Good for attic? As of 2016, the standard building code for attic insulation in L.A., Orange, Ventura and surrounding counties is R-38.
How many inches of cellulose do I need in my attic?
The recommended level for most attics is to insulate to R-38 or about 10 to 14 inches, depending on insulation type.
Should I insulate between the rafters in my attic?
The general advice we give is that you should always insulate between and above the rafters (warm roof) or between and under the rafters (cold roof).
What is the R-value of 6 inches of cellulose?
Damp-sprayed loose-fill cellulose insulation has an R-value of up to 3.7 per inch, and it also has superior sealing characteristics. A 6-inch wall cavity that’s insulated with loose-fill cellulose is expected to reach a total R-value of 22.
What R-value is 12 inches of cellulose?
| R-value of Materials and Depths | ||
|---|---|---|
| Material | R-value/in | 12″ |
| Cellulose blown (attic) | 3.2 – 3.7 | 38.4 – 44.4 |
| Cellulose blown (wall) | 3.8 – 3.9 | 45.6 – 46.8 |
| Polystrene Board | 3.8 – 5.0 | 45.6 – 60.0 |
Can attic insulation touch the roof?
Attic insulation should not touch the roof. Although it can be tempting to over insulate, resist the urge. Too much insulation hinders airflow and can keep excess moisture from escaping, especially in attics.
Should the underside of a roof be insulated? roof insulation is no-contest. The floor wins every time. Insulating the floor is standard practice for an unfinished attic space. The exception to this rule takes place when families opt to convert an unfinished attic space into something usable or livable.
Do I need baffles in my attic? Are Attic Baffles Necessary? To have a properly airy and insulated roof, you’ll want to have attic vents baffles. So while not every home will have attic soffit vents and baffles, it may be a necessary part of keeping your home safe from mold, condensation, and costly repairs.
How many inches of blown in cellulose insulation do I need?
With blown-in cellulose insulation, that would require insulation to a depth of 10 inches. If there is already insulation, measure the current depth and subtract to determine the amount needed to bring the attic to the recommended level for the desired R-Value.
What is the R-value of 4 inch of cellulose insulation?
Loose-fill cellulose insulation offers an R-value of around 3.5 per inch of thickness, while densely packed cellulose boasts an R-value between 3.8 and 4.0 per inch.
What is the R-value of 5 inches of cellulose insulation?
Subscribe to Attainable Home!
| Type of Insulation | R-Value |
|---|---|
| Fiberglass | 2.2 to 3.8 per inch, depending on loose-fill, blown-in, or fiberglass batt insulation. |
| Foam Board | Approximately R-5 per inch of thickness. |
| Rockwool | Between 3 to 3.3 for each inch of insulating material. |
| Cellulose | Between 3.2 to 4.0 per inch of thickness . |
Dec 25, 2021
What is the R-value of 8 inches of cellulose insulation?
Cellulose is not unusual in this regard. Like many insulation materials, it provides an R-value of approximately R-3.5 per inch of thickness.
How many inches is r50 blown insulation?
R 50: Thickness that oscillates between 15 and 19 inches. R 60: Thickness that oscillates between 19 and 22 inches. R 70: Thickness that oscillates between 22 and 25 inches.
How many inches is R30 blown insulation?
Fiberglass Chart
| R-Value | Thickness | Bags / 1000 Sq Ft |
|---|---|---|
| R49 | 16.25” | 22.6 |
| R44 | 14.75” | 20.1 |
| R38 | 12.75” | 16.8 |
| R30 | 10.25” | 13.0 |
What is the highest R-value for 6 inch batt insulation?
Fiberglass Insulation Batts
Fiberglass blankets or rolls provide an R-value of up to 3.2 per inch, so a 6-inch fiberglass batt may achieve an R-value of 19.2, and some high-performance products are rated at R-21.
What are the cons of blown in insulation? Cons
- This type of insulation requires professional installation.
- Installation projects can be very messy.
- The weight of blown-in cellulose can cause ceiling sag.
- Damp blown-in insulation can promote fungal growth.
- The material becomes very problematic when wet.
